Analyze the rise of biomass fuels from past data

Biomass wood pellet machine manufacturers share: 2014 annual total energy consumption of 4.26 billion tons of standard coal, an increase of 2.2% over the previous year.

 

Coal consumption decreased by 2.9 percent, crude oil consumption increased by 5.9 percent, natural gas consumption increased by 8.6 percent, and electricity consumption increased by 3.8 percent.

Coal consumption accounted for 66.0 percent of total energy consumption, and clean energy such as hydropower, wind power, nuclear power and natural gas accounted for 16.9 percent of total energy consumption.

Raw coal production fell 2.5 per cent to 3.87 billion tonnes. Natural gas production rose 7.7% to 13.016 billion cubic meters.

 

Nuclear power generation grew by 18.8%, hydropower by 15.7%, and thermal power by 0.3%.

ABC Machinery animal feed production machine Manufacture strongly present to our new products every year and produce the value addition machines for wood pelletizer industry.

How to replace the snails of the oil press

During the operation of the soybean oil machine, sometimes due to improper operation or long use time, the vulnerable parts of the oil press are damaged. In this case, it is necessary to replace the accessories. During the sales process recently, some customers are asking about the inside of the mustard oil mill Some customers are not very familiar with the oil press structure, so there will be some problems when replacing the snails. Let’s take a look at the problems that should be paid attention to when replacing the oil press in oil mill business:

(1) The method of dismantling the screw: immediately move the handle after stopping the machine to pull the press shaft out of the press chamber, remove the protective cap, hexagonal nut, round nut and adjusting bolt, and insert a 16-diameter iron rod into the lock nut Rotate clockwise in the hole (remember that the threads matching the shaft core are all left-handed), after removing the lock nut, each section of the screw can be removed. If the snails (with fine slag in the inner hole) are blocked and difficult to disassemble, you can put a wooden board on the ground, and the two of them will knock the snails a few times to remove them. If they still can’t be removed, they can be heated with wood fire. Remove.

(2) Installation of the screw press: erect the screw press with the thin end upwards, install the retaining ring, install the screw press on the shaft in turn from No. 1, and then tighten it with a lock nut to prevent the oil residue from being pressed deeply. The screw hole affects the disassembly of the screw press. (The adjusting nut makes the two ends of the adjusting bolt have 8309 bearings. When installing, the large hole surfaces of the two bearings are against the two ends of the adjusting bolt. After the screw is installed as a whole, use two (M42×62) nuts to back tightly Pay attention to the gap between the two 8309 bearings at all times. Move the adjusting bolt by hand to feel flexible when it turns.

Some customers are afraid that the order will not be found after removing the accessories. In fact, there is a simple way to mark the new accessory vendor according to the old accessory, and then install it according to the mark. There should be no problem.

Tempering time of flour machine

In the wheat flour production process, we need to go through a process, that is, tempering the wheat, which is a key step. The length of the tempering time determines the quality of the flour produced, so we are using the flour machine to process the flour. At this time, we must first reasonably control the tempening time to produce better quality flour! Next, the ABC Machinery flour mill business manufacturer will tell you how to control the wheat flour milling time! Hope it can be helpful to everyone!
 

After the raw material passes through the water machine, the water just added is mainly concentrated on the surface of the wheat grains. For the whole raw material, the distribution of water is not balanced. Therefore, the wheat after the water has to be kept in a closed state, and the surface is made by conduction and penetration. The water is evenly distributed inside the wheat grains and the whole raw material. To achieve this, the key factor is sufficient time to temper the wheat. It usually takes 8 hours for the water on the wheat skin to penetrate uniformly in the grain, and it takes about 12 hours to complete the physical and chemical combination with the internal material of the wheat, volume expansion and heat generation, and to exist in the grain structure in a relatively stable state, but It takes longer to achieve the balance of water in all the grains through the conduction between the grains. When the one-time impingement process is used, the tempering time is generally controlled between 16-30h. When the two impingement process is used, the first time is usually greater than the second time, correspondingly, the first time of dampening is about 20h, and the second time is about 16h.
 

The above content is the scope of the time control of the tempering process in the flour milling process, everyone should study hard! The length of the tempering time affects the quality of the flour, so I hope you can study the tempering time carefully and use it for yourself! ABC Machinery specializes in the production of flour production equipment such as flour mills, flour processing equipment, flour mill project, and wheat flour milling machines.

The correct disassembly steps of the pellet machine

The correct disassembly steps of the
cattle feed business pellet machine:

1. When disassembling the feed pellet machine, prepare for assembly. In order to improve the assembly efficiency and ensure the correctness of the assembly, attention should be paid to check and mark when disassembling.
2, the surface soil and oil should be removed before disassembly, and it should be kept clean during disassembly.
3, disassemble as needed, disassemble as little as possible, and do not disassemble if disassembly is not allowed.
4. When disassembling the poultry feed business pellet machine, use suitable tools, do not hit hard, so as to avoid damage or deformation of the parts.
5. The feed pellet machine should be disassembled in a reasonable order, usually from the accessories to the main part, from the outside to the inside, first disassemble the whole poultry feed making machine into an assembly, then disassemble the assembly into parts, and disassemble the parts into parts.

 

Causes and treatment of sludge from oil press

The user newly purchased a peanut oil press, which will be able to operate normally after assembly, commissioning and running-in. Normally when the peanut oil press is in normal operation, the oil enters the press chamber from the hopper, and the oil is extracted from the fifth and sixth sections of the press chamber by the collision between the snail and the oil in the press chamber and the pressure of the press chamber. The cracks in the crushed strips flow out, and the cakes are tiled from the cake outlet to the inside of the oil mill project. Why does the peanut oil press appear slag? Usually when squeezing oil, the city stops pre-processing such as frying, selection, and tampering with the oil moisture and temperature to reach the appropriate premise and stop the oil extraction. Usually, many users stop the squeezing operation under the condition that the oil is not in the proper condition because of poor skills and little experience in pressing, so slagging occurs.

Generally, the residue from the oil press is at the fifth and fourth snails near the feed end.
Slagging is divided into normal slagging and many slaggings according to the state of pressing. What should I do if the amount of slagging is large?
1. If the slag from the mustard oil mill is filamentous, it is normal in this state.
2. If the oil press slags into flakes, it is an abnormal phenomenon. The strip pressure wire of the oil press is not pressed tightly, or it may be that the strips are strictly worn and flakes appear in the abrasion area of ​​the oil eye.

How to avoid a lot of residue from peanut oil press?
1. The peanut oil press mainly needs a running-in process, and it only needs to run-in well, so that the early oil pressing capacity reduces unnecessary trouble. You can click the precautions during the running-in period of the mustard oil business press to know how to run-in the oil press.
2. If the plasticity of the oil is not good, it will be difficult to produce the cake, which will increase the pressure in the press chamber of the oil press and cause slag. For the pressed oil, the moisture content and the temperature of the oil press can be increased appropriately to increase the plasticity of the oil.
3. Regularly check and protect the important parts of the soybean oil machine, such as whether the screw is damaged, whether the nut of each part is loose, whether the slippery part needs slippery growth, etc., only good oil press equipment capabilities are required to bring users Exceptionally good benefit.

How to choose a briquette making machine?

Where is the mechanism charcoal used?
ABC Machinery charcoal making machine factory answer: the mechanism of charcoal widely used, suitable for: (1) metallurgy (iron reducing agent, aluminum smelting electrode, steel ingot insulation agent);(2) Chemical industry (used to produce carbon disulfide, calcium carbide, carbon tetrachloride, etc.);(3) Construction (concrete special packing, insulating materials, refractory materials, etc.);(4) Rural horticulture (soil improvement, water and soil protection, smoked and Fried tea, etc.); (5) Animal husbandry (feed mixture, animal blocking and deodorization);(6) Domestic fuel (heating, baking, hot pot, etc.).

How big is the site for charcoal processing? How many people operate it?
ABC Machinery plant a: for small

sugarcane charcoal machine production site need 50-80 square can, water, electricity, three-phase electricity, there is a simple shed is better, in order to protect the life of the machine and the storage of raw materials; The complete set of charcoal briquettes equipment needs 2-3 people to operate.

How to produce mechanism charcoal without technology?
ABC Machinery factory answer: after the purchase of ABC Machinery manufacturers Machinery equipment, I can send technical personnel to your home, site guidance, layout production site, also personally teach charcoal machine production operation skills, just need to provide technical personnel accommodation can.

What are the tips for choosing a charcoal machine?
At present on the market the principle of charcoal machine equipment, wood chip log making machine process flow is basically the same, but the production of equipment is very different.

The 60-ton flour mill is installed and put into production

Congratulations, the 60-ton flour mill plant of the Shandong customer Mr. Xin has been officially installed and will be put into production. The 60-ton flour mill of Mr. Xin immediately attracted the attention of many people after the installation. Why? Because Boss Xin’s factory building is very beautiful, the new factory building is clean and tidy. The floor is covered with floor tiles, which are clean and bright. The walls and roof of the factory are also made of new materials in white tones. The whole installation is equipped with our display the 60-ton complete set of flour mill process equipment can be described as tall! The surrounding residents also praised it one after another, and the sanitary conditions can be described as reassuring! Mr. Xin’s flour business will begin to be put into production immediately, and we hope that this tall plant and flour milling equipment can bring about the benefits of wealth! Here I wish Mr. Xin a prosperous business! Our after-sales service to customers will also be very perfect. If Mr. Xin has any questions that need to be consulted or if there are any minor faults in the flour mill equipment, he can contact us as soon as possible, and we will solve it for you as soon as possible!