How to replace the snails of the oil press

During the operation of the soybean oil machine, sometimes due to improper operation or long use time, the vulnerable parts of the oil press are damaged. In this case, it is necessary to replace the accessories. During the sales process recently, some customers are asking about the inside of the mustard oil mill Some customers are not very familiar with the oil press structure, so there will be some problems when replacing the snails. Let’s take a look at the problems that should be paid attention to when replacing the oil press in oil mill business:

(1) The method of dismantling the screw: immediately move the handle after stopping the machine to pull the press shaft out of the press chamber, remove the protective cap, hexagonal nut, round nut and adjusting bolt, and insert a 16-diameter iron rod into the lock nut Rotate clockwise in the hole (remember that the threads matching the shaft core are all left-handed), after removing the lock nut, each section of the screw can be removed. If the snails (with fine slag in the inner hole) are blocked and difficult to disassemble, you can put a wooden board on the ground, and the two of them will knock the snails a few times to remove them. If they still can’t be removed, they can be heated with wood fire. Remove.

(2) Installation of the screw press: erect the screw press with the thin end upwards, install the retaining ring, install the screw press on the shaft in turn from No. 1, and then tighten it with a lock nut to prevent the oil residue from being pressed deeply. The screw hole affects the disassembly of the screw press. (The adjusting nut makes the two ends of the adjusting bolt have 8309 bearings. When installing, the large hole surfaces of the two bearings are against the two ends of the adjusting bolt. After the screw is installed as a whole, use two (M42×62) nuts to back tightly Pay attention to the gap between the two 8309 bearings at all times. Move the adjusting bolt by hand to feel flexible when it turns.

Some customers are afraid that the order will not be found after removing the accessories. In fact, there is a simple way to mark the new accessory vendor according to the old accessory, and then install it according to the mark. There should be no problem.

Tempering time of flour machine

In the wheat flour production process, we need to go through a process, that is, tempering the wheat, which is a key step. The length of the tempering time determines the quality of the flour produced, so we are using the flour machine to process the flour. At this time, we must first reasonably control the tempening time to produce better quality flour! Next, the ABC Machinery flour mill business manufacturer will tell you how to control the wheat flour milling time! Hope it can be helpful to everyone!
 

After the raw material passes through the water machine, the water just added is mainly concentrated on the surface of the wheat grains. For the whole raw material, the distribution of water is not balanced. Therefore, the wheat after the water has to be kept in a closed state, and the surface is made by conduction and penetration. The water is evenly distributed inside the wheat grains and the whole raw material. To achieve this, the key factor is sufficient time to temper the wheat. It usually takes 8 hours for the water on the wheat skin to penetrate uniformly in the grain, and it takes about 12 hours to complete the physical and chemical combination with the internal material of the wheat, volume expansion and heat generation, and to exist in the grain structure in a relatively stable state, but It takes longer to achieve the balance of water in all the grains through the conduction between the grains. When the one-time impingement process is used, the tempering time is generally controlled between 16-30h. When the two impingement process is used, the first time is usually greater than the second time, correspondingly, the first time of dampening is about 20h, and the second time is about 16h.
 

The above content is the scope of the time control of the tempering process in the flour milling process, everyone should study hard! The length of the tempering time affects the quality of the flour, so I hope you can study the tempering time carefully and use it for yourself! ABC Machinery specializes in the production of flour production equipment such as flour mills, flour processing equipment, flour mill project, and wheat flour milling machines.

The correct disassembly steps of the pellet machine

The correct disassembly steps of the
cattle feed business pellet machine:

1. When disassembling the feed pellet machine, prepare for assembly. In order to improve the assembly efficiency and ensure the correctness of the assembly, attention should be paid to check and mark when disassembling.
2, the surface soil and oil should be removed before disassembly, and it should be kept clean during disassembly.
3, disassemble as needed, disassemble as little as possible, and do not disassemble if disassembly is not allowed.
4. When disassembling the poultry feed business pellet machine, use suitable tools, do not hit hard, so as to avoid damage or deformation of the parts.
5. The feed pellet machine should be disassembled in a reasonable order, usually from the accessories to the main part, from the outside to the inside, first disassemble the whole poultry feed making machine into an assembly, then disassemble the assembly into parts, and disassemble the parts into parts.