The Wood Chip Making Machine Promotes New Energy

In recent years, air pollution and smog are rampant, and energy conservation, emission reduction, and the development and use of new energy are urgent. The National Energy Administration also mentioned the new energy cooperation framework at the previous 2014 APEC meeting. APEC leaders listened to China’s energy development plan, deepened the revolution in consumption, supply, technology, and systems, and strengthened international cooperation, insisting on “saving, clean, and safe” Implements the four major strategies of “saving priority, domestically based, green and low-carbon, and innovation-driven”, through vigorously promoting energy conservation, clean and efficient development and utilization, enhancing independent guarantee capabilities, vigorously developing non-fossil energy, and promoting energy technology innovation, Measures to expand international energy cooperation, deepen energy system reform, and accelerate the construction of a clean, efficient, safe, and sustainable modern energy system. It can be seen that the development of new energy is China's top priority in the treatment of environmental pollution, and there is a long way to go in treatment and development.

 

In response to the emergence of wood chip making machines, charcoal making machine can turn agricultural and forestry wastes, such as wood chips, straw, bark, rice husk and other combustible materials into biomass rod fuel, to replace the traditional high energy consumption. Polluting energy, biomass fuel has low-carbon, environmentally friendly characteristics, convenient transportation, and raw material sources can be seen everywhere. Now biomass energy has a trend to replace traditional energy. ABC Machinery specializes in the production of sawdust briquette maker, biomass briquette machine, more products log in: www.bioenergy-machine.com.

Common problems and solutions of charcoal rod making machine

1. The effect of using the same raw material on different sawdust briquettes making machines is occasionally very different: the reason is the difference in the clearance between the rod making machine's advancing screw and the forming sleeve.

2. Smoke comes out from around the rod during rod making, and the rod made is rougher than it will be: the reason is that the raw material used for making the rod is too dry, and the clearance between the propeller and the forming cylinder is too high and the temperature is too high.

3. In the process of making the rod, it was discovered that the shot, the abnormal rod, and the eye plugging were found: the reason for this phenomenon was that the front edge of the screw propeller was worn too seriously.
4. The pay rod produced by the charcoal making machine has a certain density. If the pay rod breaks as soon as it is broken, and there is a light on the broken wall: it is because the initial position of the spiral front is too high.
5. During the process of rod making, it was found that carbonization was found when the temperature was slightly higher, but if the temperature was slightly lower, it would not be good: the forming sleeve of the rod making machine was worn too seriously.
6. Too low temperature, excessive wetness of raw materials or improper fit clearance are the important reasons that lead to unsatisfactory production and firing.
7. If the raw material of the rod is not dried and the humidity is high, the rod will bend.
8. Excessive adjustment of the propeller screw of the rod making machine or high temperature will result in poor density and fast speed of the rod.

9. The rod output rate slows down after replacing the screw with the same raw material: the screw angle of the screw is too high, it needs to be repaired and polished.
10. When the raw material is too wet or the rod cannot be produced due to other reasons, it is because the sawdust briquette press has been running for a long time and the phenomenon of gas return is found.
11. If the screw of the propeller of the horse manure brick maker is too short or worn, the rod will not be produced and the screw will run idly.
12. The rod cannot be produced and the screw is screwed: the temperature is too low, the screw is too short or worn.

Straw fuel is popular, the wood pellet machine market is booming

The increasingly prominent world energy problems have seriously affected the rapid development of social economy, and the concentrated use of fossil energy on a large scale has released a large amount of carbon dioxide, sulfur dioxide, nitrogen oxides and other substances, which have harmed the living environment of mankind. Straw fuel has been favored by more and more people because of its reusability, low pollution and universal dispersibility. We understand from the market that because straw fuel is used by more and more people, wood pelletizing equipments are extremely popular.

The sawdust pellet machine uses solid waste such as corn stalks, wheat straw, rice straw, peanut husks, corn cobs, cotton stalks, soybean stalks, weeds, branches, leaves, sawdust, bark and other solid wastes of crops as raw materials, which are crushed, pressurized, It is a machine for densification and molding to become a small rod-shaped solid particle fuel.
Xiao Zhang, who makes peanut processing, told us, “In the past, there was always no way to take these peanut shells, and there was no way to throw them away. Let’s burn them as firewood. The smoke can choke people. Now it’s fine, buy it. I used a wood pellet machine to process these peanut shells into pellet fuel for heating in winter. Nowadays, coal is becoming more and more expensive, and it’s just right to use it. Save money and worry."
We interviewed ABC Machinery, a veteran manufacturer of wood pellet machines, and the relevant person in charge told us, “Nowadays, more and more people are buying wood pellet machines, and we are also stepping up production to meet market needs. At the same time, we will discuss innovations. More products, let the wood pellet mill serve more people."

According to the prediction of the International Renewable Energy Organization, the open reserves of oil, natural gas and coal will only be used for about 60 years at the current rate of exploitation and application. Therefore, straw-based biomass energy is an important development direction of renewable energy in the future. With the global energy shortage, the market demand and profit margins for straw fuel will be immeasurable.
There is nothing wrong with choosing Anyang ABC Machinery's sawdust pelletizer, sawdust pellet machine, and sawdust shredder. It is energy-saving and environmentally friendly. Our company guarantees the quality of production and will definitely provide you with the most satisfactory service!

What are the factors that affect the output of charcoal machines

 With the development of society and the progress of science and technology, charcoal machines are also continuously updated. So far, the charcoal machines have been developed to the third generation. Both equipment quality and service have been praised by customers. As a senior charcoal machine factory, Below we cooperate to understand what are the ingredients that will always affect the output of charcoal machines.

Friends all know that the ingredients that affect the output of charcoal making machine are: the types of raw materials, equipment construction, equipment maintenance, and the skills of the workers who build the charcoal.

One: Types of raw materials
Different raw materials, using the same equipment, the output is also different. Friends know that plants are divided into woody and herbaceous.
The raw materials of the wood family have high carbon content and low ash content, so the charcoal output will be high, and the charcoal produced has a high calorie, and it is also a very popular charcoal in the current environmental trend.
The raw materials of the grass family have low carbon content and high ash content, so the amount of charcoal will be greatly reduced, and the calories of the charcoal produced are not as high as the calories of the wood family. It can only be used for home use, so sales are not too ideal.
2: Equipment construction
A good horse is equipped with a good saddle. Only the equipment construction is very good, which can greatly improve the output of the biomass briquettes machine. Many customers purchase the charcoal briquette machine with cheap temporary plans and choose very cheap equipment. As everyone knows, this is the case. It hurts me. The equipment costs of each production factory are controlled by the old, steel material costs, labor costs, water and electricity costs, etc. The factory will not do a loss-making business. The cheaper the equipment you buy, the more the factory uses. The thinner the raw material, the lower the power of the motor. For a long time, the equipment not only consumes fast, but the output of small horse-drawn carts is not much higher.
 

3: Equipment maintenance
No matter what things are carefully maintained, you only need not to raise them. Sooner or later, I will pick you up. The very important thing in maintenance is the propeller of the sawdust briquette machine. It must be polished and corrected every time it is used. The other is to add grease to the equipment. Clearing out sundries for equipment, etc. There are specific analyses on the analysis books of the factories that require maintenance.
4: The skills of workers who build charcoal
Every production joint has strict requirements, such as the size of the raw material crushing, the humidity of the raw material, the proportion of each raw material entering the carbon when a variety of raw materials are mixed, the carbonization time during the carbonization, the temperature control, etc. If the worker does not mastering these techniques, whether it’s spicy, it’s not a good job, or the charcoal produced by the carbonization is not enough. It wastes raw materials and delays time.

Process of flat die wood pellet machine

 Biomass fuel granulation process. The basic process steps of biomass granulation are roughly similar. However, due to the different physical properties of the raw materials and the different working principles of the forming wood pellet machine, the specific process is still different. The key process steps of the flat die machine are specific. The introduction is as follows:

In the crushing process, when the flat mold is used for granulation, the smaller the particle size of the raw material, the easier it is for the particles to fill and fit each other. Therefore, the average energy consumption per unit output of the granulator is smaller. The wear speed is also slower, and the water permeability and hardness of the particles are higher. However, blindly pursuing the reduction of particle size will cause the energy consumption of the crushing process to rise sharply. Therefore, it should meet the processing requirements of flat die granulators under the premise of, make the particle size as large as possible. In fact, it is one of the advantages of the flat die wood pellet maker to be able to suppress large-size raw materials. Generally, for crop straw and other raw materials, the maximum particle size is required to be less than 2×2×30mm, while for wood raw materials, the requirements are more stringent.

In the granulation process, the dried material enters the granulation process and can be processed directly without quenching and tempering. Conditional manufacturers can choose automatic control system and die roll automatic gap adjustment device. The automatic control system adjusts the frequency converter of the feeding motor according to the change of the host current, so as to adjust the feeding amount in real time, which can effectively avoid the occurrence of machine blockage. The die roll automatic gap adjustment device can collect die roll gap data, and control the hydraulic system through feedback and comparison, so that the gap is consistent with the set value, and can be changed at any time during the production process. Generally speaking, the grinding roller gap should be as small as possible during the starting phase, which can reduce the starting torque and reduce the motor load. After entering the steady state work, the grinding roller gap should be slightly larger, which can increase the compression stroke and obtain hard and smooth particles. The setting of the gap change with time can be input into the control system. After starting, the machine can automatically adjust the die roll gap. Pressure rollers and flat molds are easy to wear parts and need to be replaced regularly. The service life of pressure rollers can be slightly longer, but it is best to replace the flat molds together. Generally, flat molds can work for 800-2000 hours, depending on the material and processing technology of the parts. According to the test results, the PM60 flat die pelletizer is suitable for processing biomass materials such as sawdust, sawdust and straw mixture, with a molding rate of over 93%, power consumption per ton under 55 kWh, and an hourly production capacity of about 800kg-900kg. There is nothing wrong with choosing Anyang ABC Machinery's pelletizing machine, sawdust pellet machine, and sawdust crusher. It is energy-saving and environmentally friendly. Our company guarantees product quality and will definitely provide you with the most satisfactory service!

wood pellet mill mold high specification treatment

The wood pellet mill is an emerging industry, the market prospect is broad, the support of national policies, the momentum of the past two years, the rapid development.

The mold of the hemp pellet mill has high hardness, strength, red hardness, wear resistance and toughness of the steel, but also has good high temperature strength, thermal fatigue stability, thermal conductivity and corrosion resistance, but also requires high hardenability, in order to ensure that the whole section has the same mechanical properties.

In addition, small thermal deformation, good machining performance, maintenance of welding performance and working conditions, size and shape stability. The carbon content in the die steel must be appropriate for the carbon alloy structural steel. The first-class steel smelting adds more alloying elements eutectoid or hypereutectoid steel, so the price is expensive, several times more than the general price of ordinary carbon structural steel.

This alloy steel and the need to use better multiple heat treatment process, ordinary carbon steel only needs a simple quenching heat treatment process, the heat treatment cost is naturally much higher than the ordinary steel manufacturing mold price. But its use of durable shapes, forming stable shapes and repeated many times for maintenance increases the reliability of molds compared to ordinary materials. Remind the majority of users to choose the pellet machine can not only pay attention to the price level, more is concerned about the quality of the pto pellet mill, pay attention to the quality of the core parts of the mold pellet machine, rather than dumping cheap suffer a great loss.

Operation method of pellet machine

The operation method of the pellet machine. In animal feed business when the customer uses the pellet machine, there may be some other reasons that cause problems in the pellet machine production process.

Nowadays, many customers cannot achieve the ideal production because the pellet machine is used incorrectly. Efficiency, so when you use the pellet machine for actual production, you need to constantly master new technologies. The following is the experience accumulated in the actual production process, combined with some customer feedback opinions, some tips summarized: 1. Feeding should be even. This has the advantage of making the granulation of the animal feed manufacturing process machine smoother and keeping the machine running at high speed. 2. Choose the appropriate template aperture according to your own use. Some users use too small apertures, and often have low output or even no discharge. They hope to ask the salesperson carefully when buying a pellet machine what size template should be equipped. 3. Adjust the gap between the template and the pressure roller. Appropriate pressure can achieve a good effect on the maturation and compactness of the particles. 4. Keep the pellet machine clean. Users often do not pay attention to keeping the poultry feed plant clean during use, which speeds up the life of the pellet machine, so pay attention to keeping the feed making machine clean. It is best to clean up regularly. 5. Regularly keep the granules lubricated, and add butter and lubricant regularly. Regularly cleaning the template, and generally adding butter can improve the efficiency of the machine.