Common problems and solutions of charcoal rod making machine

1. The effect of using the same raw material on different sawdust briquettes making machines is occasionally very different: the reason is the difference in the clearance between the rod making machine's advancing screw and the forming sleeve.

2. Smoke comes out from around the rod during rod making, and the rod made is rougher than it will be: the reason is that the raw material used for making the rod is too dry, and the clearance between the propeller and the forming cylinder is too high and the temperature is too high.

3. In the process of making the rod, it was discovered that the shot, the abnormal rod, and the eye plugging were found: the reason for this phenomenon was that the front edge of the screw propeller was worn too seriously.
4. The pay rod produced by the charcoal making machine has a certain density. If the pay rod breaks as soon as it is broken, and there is a light on the broken wall: it is because the initial position of the spiral front is too high.
5. During the process of rod making, it was found that carbonization was found when the temperature was slightly higher, but if the temperature was slightly lower, it would not be good: the forming sleeve of the rod making machine was worn too seriously.
6. Too low temperature, excessive wetness of raw materials or improper fit clearance are the important reasons that lead to unsatisfactory production and firing.
7. If the raw material of the rod is not dried and the humidity is high, the rod will bend.
8. Excessive adjustment of the propeller screw of the rod making machine or high temperature will result in poor density and fast speed of the rod.

9. The rod output rate slows down after replacing the screw with the same raw material: the screw angle of the screw is too high, it needs to be repaired and polished.
10. When the raw material is too wet or the rod cannot be produced due to other reasons, it is because the sawdust briquette press has been running for a long time and the phenomenon of gas return is found.
11. If the screw of the propeller of the horse manure brick maker is too short or worn, the rod will not be produced and the screw will run idly.
12. The rod cannot be produced and the screw is screwed: the temperature is too low, the screw is too short or worn.

Straw fuel is popular, the wood pellet machine market is booming

The increasingly prominent world energy problems have seriously affected the rapid development of social economy, and the concentrated use of fossil energy on a large scale has released a large amount of carbon dioxide, sulfur dioxide, nitrogen oxides and other substances, which have harmed the living environment of mankind. Straw fuel has been favored by more and more people because of its reusability, low pollution and universal dispersibility. We understand from the market that because straw fuel is used by more and more people, wood pelletizing equipments are extremely popular.

The sawdust pellet machine uses solid waste such as corn stalks, wheat straw, rice straw, peanut husks, corn cobs, cotton stalks, soybean stalks, weeds, branches, leaves, sawdust, bark and other solid wastes of crops as raw materials, which are crushed, pressurized, It is a machine for densification and molding to become a small rod-shaped solid particle fuel.
Xiao Zhang, who makes peanut processing, told us, “In the past, there was always no way to take these peanut shells, and there was no way to throw them away. Let’s burn them as firewood. The smoke can choke people. Now it’s fine, buy it. I used a wood pellet machine to process these peanut shells into pellet fuel for heating in winter. Nowadays, coal is becoming more and more expensive, and it’s just right to use it. Save money and worry."
We interviewed ABC Machinery, a veteran manufacturer of wood pellet machines, and the relevant person in charge told us, “Nowadays, more and more people are buying wood pellet machines, and we are also stepping up production to meet market needs. At the same time, we will discuss innovations. More products, let the wood pellet mill serve more people."

According to the prediction of the International Renewable Energy Organization, the open reserves of oil, natural gas and coal will only be used for about 60 years at the current rate of exploitation and application. Therefore, straw-based biomass energy is an important development direction of renewable energy in the future. With the global energy shortage, the market demand and profit margins for straw fuel will be immeasurable.
There is nothing wrong with choosing Anyang ABC Machinery's sawdust pelletizer, sawdust pellet machine, and sawdust shredder. It is energy-saving and environmentally friendly. Our company guarantees the quality of production and will definitely provide you with the most satisfactory service!